Aruba 530 Series Access Point

Wi-Fi ThroughPut Technical Specification
AP type  Indoor, dual radio, 5GHz and 2.4GHz 802.11ax
4×4 MIMO
Interface  E0, E1: HPE SmartRate port (RJ-45, maximum negotiated
speed 5Gbps)
USB Port 2.0 host interface
PoE-P0wered 26.4W
DC power   23.3W
Transmit power Configurable in increments of 0.5 dBm
Operating conditions Temperature: 0C to +50C / +32F to+122F
Hardware Variant AP-534: External antenna models
AP-535: Internal antenna models
Warranty Aruba Hardware Limited Lifetime Warranty
 DC power interface : 48Vdc (nominal, +/- 5%), accepts

Description

Aruba 530 Series Access Point

High speed. High performance indoor Wi-Fi 6 APs

Connectivity across high-density deployments such as larger office spaces, training and meeting facilities, and hospitals. Up to 2.97 Gbps maximum real-world speed and maximum of 1,024 associated clients per radio.

Wi-Fi 6 OFDMA and MU-MIMO, plus ClientMatch

Handles multiple clients on each channel, regardless of device or traffic type, using AI to eliminate sticky client issues.

Air Slice for SLA-grade performance

Provides service level agreement-grade performance for latency-sensitive, high-bandwidth, and IoT services.

WPA3 and Enhanced Open security

Increases enterprise-level security without increasing complexity, and ensures stronger guest access protections.

IoT-ready Bluetooth 5 and Zigbee support

Simplifies deploying and managing IoT location services, asset-tracking services, security solutions, and IoT sensors.

Flexible management options

Options to deploy in distributed or campus modes using a cloud-hosted or on-prem management and orchestration engine

Wi-Fi Radio Specifications
  • AP type: Indoor, dual radio, 5GHz and 2.4GHz 802.11ax 4×4 MIMO
  • 5GHz radio: Four spatial stream HE80 (or 2SS HE160) MIMO for up to 2.4Gbps wireless data rate
  • 2.4GHz radio: Four spatial stream HE40 (HE20) MIMO for up to 1,147Mbps (574Mbps) wireless data rate
  • Support for up to 1,024 associated client devices per radio, and up to 16 BSSIDs per radio
  • Supported frequency bands (country-specific restrictions apply):
    • 2.400 to 2.4835GHz ISM
    • 5.150 to 5.250GHz U-NII-1
    • 5.250 to 5.350GHz U-NII-2A
    • 5.470 to 5.725GHz U-NII-2C
    • 5.725 to 5.850GHz U-NII-3/ISM
    • 5.850 to 5.895GHz U-NII-4
  • Available channels: Dependent on configured regulatory domain
  • Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
    • Including Zero-Wait DFS (ZWDFS) to accelerate channel changes
  • Supported radio technologies:
    • 802.11b: Direct-sequence spread-spectrum (DSSS)
    • 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
    • 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 37 resource units (for an 80MHz channel)
  • Supported modulation types:
    • 802.11b: BPSK, QPSK, CCK
    • 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM (proprietary extension)
    • 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM (proprietary extension)
    • 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM
  • 802.11n high-throughput (HT) support: HT20/40
  • 802.11ac very high throughput (VHT) support: VHT20/40/80/160
  • 802.11ax high efficiency (HE) support: HE20/40/80/160
  • Supported data rates (Mbps):
    • 802.11b: 1, 2, 5.5, 11
    • 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
    • 802.11n: 6.5 to 600 (MCS0 to MCS31, HT20 to HT40), 800 with 256-QAM
    • 802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4, VHT20 to VHT160), 2,166 with 1024-QAM
    • 802.11ax (2.4GHz): 3.6 to 1,147 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE40)
    • 802.11ax (5GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE160)
  • 802.11n/ac packet aggregation: A-MPDU, A-MSDU
  • Transmit power: Configurable in increments of 0.5 dBm
  • Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):
    • 2.4 GHz band: +24 dBm (18dBm per chain)
    • 5 GHz band: +24 dBm (18 dBm per chain)
    • Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain.
  • Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks
  • Maximum ratio combining (MRC) for improved receiver performance
  • Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
  • Space-time block coding (STBC) for increased range and improved reception
  • Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
  • Transmit beam-forming (TxBF) for increased signal reliability and range
  • 802.11ax Target Wait Time (TWT) to support low-power client devices
Wi-Fi Antennas
  • AP-534: Four (female) RP-SMA connectors for external dual band antennas (A0 through A3, corresponding with radio chains 0 through 3). Worst-case internal loss
    between radio interface and external antenna connectors (due to diplexing circuitry): 0.8dB in 2.4GHz and 1.3dB in 5GHz.
  • AP-535: Four integrated dual-band downtilt omni- directional antennas for 4×4 MIMO with peak antenna gain of 3.5dBi in 2.4GHz and 5.4dBi in 5GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees.
    • A mix of horizontally and vertically polarized antenna elements is used
    • Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the combined, average pattern is 1.9dBi in 2.4GHz and 3.5dBi in 5GHz.

Security

  • Integrated wireless intrusion protection offers threat protection and mitigation, and eliminates the need for separate RF sensors and security appliances
  • IP reputation and security services identify, classify, and block malicious files, URLs and IPs, providing comprehensive protection against advanced online threats
  • Integrated Trusted Platform Module (TPM) for secure storage of credentials and keys

Networking on a budget

With the integrated BLE and supporting 802.3af power, the Series APs enable enterprises to improve their work efficiency and productivity with the lowest TCO. When Ethernet drops are not available, VPN tunnels extend remote locations to corporate resources and wireless mesh connections.

Highly secure and reliable performance

The Series APs offer improved network simplicity and security in several ways. Dynamic Segmentation automatically enforces real-time, device-level access policies on Aruba wired and wireless networks. Additionally, Aruba AppRF technology leverages deep- packet inspection to classify and block, prioritize, or limit bandwidth for over 2,500 enterprise apps or groups of apps.

Flexible management options

Available management solutions include Aruba Central (available in cloud-managed and on-premises options), as well as Aruba AirWave, which supports multi-vendor networks. APs can be deployed with zero-touch provisioning to reduce deployment time, centralize configuration, and simplify inventory management.

 

Aruba Access Point

Aruba Indoor Access Point

Aruba 303 Series Access Point

Aruba 340 Series Access Point

Aruba 500 Series Access Point

Aruba 510 Series Access Point

Aruba 530 Series Access Point

Aruba 550 Series Access Point

Aruba 610 Series Access Point

Aruba 630 Series Access Point

Aruba 650 Series Access Point

Aruba Outdoor Access Point

Aruba 318 Series Access Point

Aruba 360 Series Access Point

Aruba EX370 Series Access Point

Aruba 370 Series Access Point

Aruba 387 Series Access Point

Aruba 518 Series Access Point

Aruba 560 Series Access Point

Aruba EX560 Series Access Point

Aruba 570 Series Access Point

Aruba EX570 Series Access Point

Aruba 580 Series Access Point

Aruba Ex580 Series Access Point

Aruba Remote Access Point

Aruba 203R Series Access Point

Aruba 303H Series Access Point

Aruba 500H Series Access Point

Buy Aruba Access Point online from Firewall Firm’s IT Monteur Store

Sales Number : +91 95 8290 7788
Support Number : +91 94 8585 7788
Sales Email : sales@itmonteur.net
Support Email : support@itmonteur.net

Register & Request Quote
Submit Support Ticket